Plastic mixer operation, installation, performance, and maintenance instructions

Installation of plastic mixer.
Installation: Place the horizontal mixer steadily, install the supporting feet, level them, and allow the machinery to operate freely. Before use, add oil to the parts that need to be oiled, and then perform no-load operation to check whether the fasteners are loose, whether the electricity is normal, and whether the mechanical operation is normal. If there are any abnormalities, repair and debug them. Turn the charging port to the top, open the charging cover to charge, and the charging amount should not be specified. Then close the charging cover and start the machine to run. If any abnormalities are found during transportation, please stop the machine for inspection.
Performance characteristics and usage instructions of plastic mixers.
Plastic mixer is a small feed equipment designed for rural farmers, small farms, and small to medium-sized compound feed factories. You can also mix putty powder with chemical raw materials, which has a good effect. Integrating vertical, mixing bin, and horizontal transportation. It has the advantages of simple and compact structure, low one-time investment, economic practicality, convenient maintenance, and no need for a production site.
The material to be mixed is added to the plastic mixer from the lower feeding port. The mixed material enters the vertical screw conveyor from the feeding hopper of the plastic mixer through the screw in the plastic mixer, and then flies in an umbrella shape, falling around the mixing barrel. It enters the vertical screw conveyor again from the gap at the bottom of the sleeve, and then rises again. This way, the mixture is stirred until it is evenly mixed, and then the discharge port is opened for discharge. It is worth noting that although feed mixers can produce efficiency, there are also risks involved. Farmers should pay attention to operating standards when using feed mixers. Before using the mixer, in addition to checking the entire machine, the belt tension should also be adjusted. After starting up, use a powder machine weighing about 15 kilograms to observe whether the machine can discharge materials normally. After officially using the plastic mixer, do not feed with your hands or wooden sticks to avoid getting your hands caught in the machine.
Performance characteristics of plastic mixer: 1. Mixing and drying are synchronized because the material maintains continuous flow during the drying process, with uniform heat penetration and short drying time, making it difficult to quickly knot; 2. The standard model is a double-layer barrel design, with an inner layer made of stainless steel. The effect of installing intermediate layers and insulation materials. 3. High frequency heaters have fast heating, low power consumption, and a comprehensive drying cost of 20 yuan per ton of material; 4. Double tube dehumidification outlet can effectively remove moisture and dust, without polluting the working environment.
Plastic mixer operation instructions: 1. Before use, an idle test should be conducted; 2. Idle testing. Large vertical mixers can only be put into production without abnormal noise, bearing stall heating, and gearbox temperature rise. Before debugging, check the integrity of the joints of the large plastic mixer, the lubricating oil inside the reducer, and the electrical equipment. Then, close the main switch, connect the power, and perform idle debugging. If the machine vibrates abnormally or makes abnormal noise during use, the large plastic mixer should be stopped for inspection. 4. The shaft seals at both ends of the mixing screw should be kept clean to prevent the plastic from turning black and deteriorating. The outer gears at both ends of the large mixing drum should have square holes and be unobstructed. Do not block the large plastic mixer to prevent back pressure, which can cause dirt to seep into the shaft and cause the material inside the barrel to turn black and deteriorate. 5. Management personnel are familiar with the performance, structure, control structure, and operating principles of large plastic mixers. Do not leave the workplace during operation to avoid malfunctions and damage to machine parts and production.
Maintenance methods for plastic mixers:
1. Regularly inspect the parts, once or twice a month. Check for flexible rotation and wear of moving parts such as worm gears, bearings, and shaft seals. If defects are found, they should be repaired in a timely manner for normal use.
2. The electrical control part should be kept clean and sensitive, and any faults should be promptly repaired.
3. After one-time use or shutdown, remove excess materials from the plastic vertical mixer and brush off residual powder from various parts of the machine. If the machine does not work for a long time, wipe it clean and cover it with a cloth.
When loading and unloading the mixing blade of a plastic mixer, care should be taken during disassembly, stable installation, and handling to avoid deformation and damage.